FAXAM 22 EXXON COMPANY, U.S.A DATE ISSUED: 03/22/99 SUPERSEDES DATE: 01/24/97 MATERIAL SAFETY DATA SHEET _______________________________________________________________________________ SECTION 1: PRODUCT AND COMPANY IDENTIFICATION _______________________________________________________________________________ COMPANY: EXXON COMPANY, U.S.A. P.O. BOX 2180 HOUSTON, TX 77252-2180 PRODUCT NAME PRODUCT CODE FAXAM 22 341481 PRODUCT CATEGORY Petroleum Lubricating Oil MEDICAL EMERGENCY TELEPHONE NUMBER: (713) 656-3424 TRANSPORTATION EMERGENCY TELEPHONE NUMBERS (BAYTOWN) (281) 834-3296 (CHEMTREC) 1-800-424-9300 Product Information and Technical Assistance: 1-800-443-9966 FAXED MSDSs: 1-800-298-4007 MAILED MSDSs OR OTHER ASSISTANCE: (713) 656-5949 ________________________________________________________________________________ SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS ________________________________________________________________________________ CAS NO. OF APPROXIMATE COMPONENTS COMPONENTS CONCENTRATION Distillates (petroleum), solvent- 64742-65-0 100% dewaxed heavy paraffinic or or Distillates (petroleum), hydrotreated 64742-54-7 heavy paraffinic SEE SECTION 8 FOR EXPOSURE LIMITS ________________________________________________________________________________ SECTION 3: HAZARDS IDENTIFICATION ________________________________________________________________________________ EMERGENCY OVERVIEW OSHA REQUIRED LABEL INFORMATION In compliance with hazard and right-to-know requirements, where applicable OSHA Hazard Warnings may be found on the label, bill of lading or invoice accompanying this shipment. Note: Product label may contain non-OSHA related information also. HAZARDOUS MATERIALS IDENTIFICATION SYSTEM (HMIS) Health Flammability Reactivity BASIS 1 1 0 Recommended by Exxon NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) - HAZARD IDENTIFICATION Health Flammability Reactivity BASIS 1 1 0 Recommended by Exxon VARIABILITY AMONG INDIVIDUALS Health studies have shown that many petroleum hydrocarbons and synthetic lubricants pose potential human health risks which may vary from person to person. As a precaution, exposure to liquids, vapors, mists or fumes should be minimized. EFFECTS OF OVEREXPOSURE (Signs and symptoms of exposure) Prolonged or repeated skin contact may cause skin irritation. PRE-EXISTING MEDICAL CONDITIONS WHICH MAY BE AGGRAVATED BY EXPOSURE None recognized ________________________________________________________________________________ SECTION 4: FIRST AID MEASURES ________________________________________________________________________________ EYE CONTACT If splashed into the eyes, flush with clear water for 15 minutes or until irritation subsides. If irritation persists, call a physician. SKIN In case of skin contact, remove any contaminated clothing and wash skin with soap and water. Launder or dry-clean clothing before reuse. If product is injected into or under the skin, or into any part of the body, regardless of the appearance of the wound or its size, the individual should be evaluated immediately by a physician as a surgical emergency. Even though initial symptoms from high pressure injection may be minimal or absent, early surgical treatment within the first few hours may significantly reduce the ultimate extent of injury. INHALATION Vapor pressure is very low. Vapor inhalation under ambient conditions is normally not a problem. If overcome by vapor from hot product, immediately remove from exposure and call a physician. If breathing is irregular or has stopped, start resuscitation; administer oxygen, if available. If overexposed to oil mist, remove from further exposure until excessive oil mist condition subsides. INGESTION If ingested, DO NOT induce vomiting; call a physician immediately. ________________________________________________________________________________ SECTION 5: FIRE-FIGHTING MEASURES ________________________________________________________________________________ FLASH POINT (MINIMUM) AUTOIGNITION TEMPERATURE 179~C (355~F) Greater than 260~C (500~F) ASTM D 92, Cleveland Open Cup FLAMMABLE OR EXPLOSIVE LIMITS (APPROXIMATE PERCENT BY VOLUME IN AIR) Estimated values: Lower Flammable Limit 0.9% Upper Flammable Limit 7% EXTINGUISHING MEDIA AND FIRE FIGHTING PROCEDURES Foam, water spray (fog), dry chemical, carbon dioxide and vaporizing liquid type extinguishing agents may all be suitable for extinguishing fires involving this type of product, depending on size or potential size of fire and circumstances related to the situation. Plan fire protection and response strategy through consultation with local fire protection authorities or appropriate specialists. The following procedures for this type of product are based on the recommendations in the National Fire Protection Association's "Fire Protection Guide on Hazardous Materials", Tenth Edition (1991): Use water spray, dry chemical, foam or carbon dioxide to extinguish the fire. Use water to keep fire-exposed containers cool. If a leak or spill has not ignited, use water spray to disperse the vapors and to provide protection for persons attempting to stop a leak. Water spray may be used to flush spills away from exposures. Minimize breathing of gases, vapor, fumes or decomposition products. Use supplied-air breathing equipment for enclosed or confined spaces or as otherwise needed. DECOMPOSITION PRODUCTS UNDER FIRE CONDITIONS Fumes, smoke, carbon monoxide, sulfur oxides, aldehydes and other decomposition products, in the case of incomplete combustion. ________________________________________________________________________________ SECTION 6: ACCIDENTAL RELEASE MEASURES ________________________________________________________________________________ CLEAN WATER ACT / OIL POLLUTION ACT This product may be classified as an oil under Section 311 of the Clean Water Act, and under the Oil Pollution Act. Discharges or spills into or leading to surface waters that cause a sheen must be reported to the National Response Center (1-800-424-8802). STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED Recover free product. Add sand, earth or other suitable absorbent to spill area. Minimize breathing vapors. Minimize skin contact. Open all windows and doors. Keep product out of sewers and watercourses by diking or impounding. Advise authorities if product has entered or may enter sewers, watercourses, or extensive land areas. Assure conformity with applicable governmental regulations. ________________________________________________________________________________ SECTION 7: STORAGE AND HANDLING ________________________________________________________________________________ HANDLING PRECAUTIONS Use product with caution around heat, sparks, pilot lights, static electricity, and open flame. "EMPTY" CONTAINER WARNING "Empty" containers retain residue (liquid and/or vapor) and can be dangerous. DO NOT PRESSURIZE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND OR EXPOSE SUCH CONTAINERS TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION; THEY MAY EXPLODE AND CAUSE INJURY OR DEATH. Do not attempt to refill or clean containers since residue is difficult to remove. "Empty" drums should be completely drained, properly bunged and promptly returned to a drum reconditioner. All other containers should be disposed of in an environmentally safe manner and in accordance with governmental regulations. For work on tanks refer to Occupational Safety and Health Administration regulations, ANSI Z49.1, and other governmental and industrial references pertaining to cleaning, repairing, welding, or other contemplated operations. ________________________________________________________________________________ SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION ________________________________________________________________________________ EXPOSURE LIMIT FOR TOTAL PRODUCT BASIS 5 mg/m3 for oil mist (aerosol) for OSHA Regulation 29 CFR 1910.1000 and an 8-hour workday recommended by the American Conference of Governmental Industrial Hygienists (ACGIH). ACGIH states that the air is to be sampled by a method that does not collect vapor; in addition, it lists a 10 mg/m3 STEL. VENTILATION Use local exhaust to capture vapor, mists or fumes, if necessary. Provide ventilation sufficient to prevent exceeding recommended exposure limit or buildup of explosive concentrations of vapor in air. No smoking, or use of flame or other ignition sources. RESPIRATORY PROTECTION Use supplied-air respiratory protection in confined or enclosed spaces, if needed. PROTECTIVE GLOVES Use chemical-resistant gloves, if needed, to avoid prolonged or repeated skin contact. EYE PROTECTION Use splash goggles or face shield when eye contact may occur. OTHER PROTECTIVE EQUIPMENT Use chemical-resistant apron or other impervious clothing, if needed, to avoid contaminating regular clothing, which could result in prolonged or repeated skin contact. WORK PRACTICES / ENGINEERING CONTROLS To prevent fire or explosion risk from static accumulation and discharge, effectively bond and/or ground product transfer system in accordance with (THE) National Fire Protection Association PUBLICATIONS. Keep containers closed when not in use. Do not store near heat, sparks, flame or strong oxidants. In order to prevent fire or explosion hazards, use appropriate equipment. Information on electrical equipment appropriate for use with this product may be found in the latest edition of the National Electrical Code (NFPA-70). This document is available from the National Fire Protection Association, Batterymarch Park, Quincy, Massachusetts 02269. PERSONAL HYGIENE Minimize breathing vapor, mist or fumes. Avoid prolonged or repeated contact with skin. Remove contaminated clothing; launder or dry-clean before re-use. Remove contaminated shoes and thoroughly clean before re-use; discard if oil-soaked. Cleanse skin thoroughly after contact, before breaks and meals, and at end of work period. Product is readily removed from skin by waterless hand cleaners followed by washing thoroughly with soap and water. ________________________________________________________________________________ SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES ________________________________________________________________________________ The following data are approximate or typical values and should not be used for precise design purposes. BOILING RANGE VAPOR PRESSURE IBP Approximately 277~C (530~F) Less than 0.01 mm Hg @ 20~C by ASTM D 2887 SPECIFIC GRAVITY (15.6~C/15.6~C) VAPOR DENSITY (AIR = 1) 0.89 Greater than 5 MOLECULAR WEIGHT PERCENT VOLATILE BY VOLUME Approximately 330 Negligible from open container in 4 hours @ 38~C (100~F) EVAPORATION RATE @ 1 ATM. AND 25~C pH (77~F) (n-BUTYL ACETATE = 1) Essentially neutral Less than 0.01 SOLUBILITY IN WATER @ 1 ATM. POUR, CONGEALING OR MELTING POINT AND 25~C (77~F) -1~C (30~F) Negligible; less than 0.1% Pour Point by ASTM D 97 VISCOSITY 21 cSt @ 40~C PRODUCT APPEARANCE AND ODOR Clear liquid, light yellow color Mild, bland petroleum odor ________________________________________________________________________________ SECTION 10: STABILITY AND REACTIVITY ________________________________________________________________________________ This product is stable and will not react violently with water. Hazardous polymerization will not occur. Avoid contact with strong oxidants such as liquid chlorine, concentrated oxygen, sodium hypochlorite, calcium hypochlorite, etc., as this presents a serious explosion hazard. ________________________________________________________________________________ SECTION 11: TOXICOLOGICAL INFORMATION ________________________________________________________________________________ NATURE OF HAZARD AND TOXICITY INFORMATION Repeated and prolonged overexposure to oil mists may result in droplet deposition, oil granuloma formation, inflammation and increased incidence of infection. In accordance with the current OSHA Hazard Communication Standard criteria, this product does not require a cancer hazard warning. This is because the product is formulated from base stocks which are severely hydrotreated, severely solvent extracted, and/or processed by mild hydrotreatment and extraction. Alternatively, it may consist of components not otherwise affected by IARC criteria, such as atmospheric distillates or synthetically derived materials, and as such is not characterized by current IARC classification criteria. Prolonged or repeated skin contact with this product tends to remove skin oils, possibly leading to irritation and dermatitis; however, based on human experience and available toxicological data, this product is judged to be neither a "corrosive" nor an "irritant" by OSHA criteria. Product contacting the eyes may cause eye irritation. Product has a low order of acute oral and dermal toxicity, but minute amounts aspirated into the lungs during ingestion or vomiting may cause mild to severe pulmonary injury and possibly death. This product is judged to have an acute oral LD50 (rat) greater than 5 g/kg of body weight, and an acute dermal LD50 (rabbit) greater than 3.16 g/kg of body weight. ________________________________________________________________________________ SECTION 12: ECOLOGICAL INFORMATION ________________________________________________________________________________ Do not discharge this product into public waters or waterways unless authorized by a National Pollution Discharge Elimination System (NPDES) permit issued by the Environmental Protection Agency (EPA). Environmental and Ecological data may be available for this product. Write or call Exxon to obtain further information. Refer to Section 6 and Section 15 for Accidental Release information and Regulatory Reporting information. ________________________________________________________________________________ SECTION 13: DISPOSAL CONSIDERATION ________________________________________________________________________________ Options for disposal of this product may depend on the conditions under which it was used. To determine the proper method of disposal, refer to RCRA (40 CFR 261), as well as federal EPA and state and local regulations. Please refer to Sections 5, 6 and 15 for additional information. ________________________________________________________________________________ SECTION 14: TRANSPORTATION INFORMATION ________________________________________________________________________________ TRANSPORTATION INCIDENT INFORMATION For further information relative to spills resulting from transportation incidents, refer to latest Department of Transportation Emergency Response Guidebook for Hazardous Materials Incidents. U.S. DOT HAZARDOUS MATERIALS SHIPPING DESCRIPTION Not regulated ________________________________________________________________________________ SECTION 15: REGULATORY INFORMATION ________________________________________________________________________________ U.S. FEDERAL REGULATIONS THE FOLLOWING INFORMATION MAY BE USEFUL IN COMPLYING WITH VARIOUS STATE AND FEDERAL LAWS AND REGULATIONS UNDER VARIOUS ENVIRONMENTAL STATUTES: THRESHOLD PLANNING QUANTITY (TPQ), EPA REGULATION 40 CFR 355 (SARA Sections 301-304) No TPQ for product or any constituent greater than 1% or 0.1% (carcinogen). TOXIC CHEMICAL RELEASE REPORTING, EPA REGULATION 40 CFR 372 (SARA Section 313) No toxic chemical is present greater than 1% or 0.1% (carcinogen). HAZARDOUS CHEMICAL REPORTING, EPA REGULATION 40 CFR 370 (SARA Sections 311-312) EPA Hazard Classification Code: Not Applicable TOXIC SUBSTANCES CONTROL ACT (TSCA) This product, as manufactured by Exxon, does not contain polychlorinated biphenyls (PCB's). All components of this product are listed on the U.S. TSCA inventory. ________________________________________________________________________________ SECTION 16: OTHER INFORMATION ________________________________________________________________________________ The health and safety information presented herein must be used in conjunction with the pertinent standards for training, work practices and facilities design established by OSHA, NIOSH, NFPA, API, NEC, NSC, UNDERWRITERS, BUREAU OF MINES, and similar organizations. The information and recommendations contained herein are, to the best of Exxon's knowledge and belief, accurate and reliable as of the date issued. Exxon does not warrant or guarantee their accuracy or reliability, and Exxon shall not be liable for any loss or damage arising out of the use thereof. The information and recommendations are offered for the user's consideration and examination, and it is the user's responsibility to satisfy itself that they are suitable and complete for its particular use. If buyer repackages this product, legal counsel should be consulted to insure proper health, safety and other necessary information is included on the container. The Environmental Information included under Section 15 hereof as well as the Hazardous Materials Identification System (HMIS) and National Fire Protection Association (NFPA) ratings have been included by Exxon Company, U.S.A. in order to provide additional health and hazard classification information. The ratings recommended are based upon the criteria supplied by the developers of these rating systems, together with Exxon's interpretation of the available data.