§  195.3 Matter incorporated by reference.

(a) Any document or portion thereof incorporated by reference in this part is included in this part as though it were printed in full. When only a portion of a document is referenced, then this part incorporates only that referenced portion of the document and the remainder is not incorporated. Applicable editions are listed in paragraph (c) of this section in parentheses following the title of the referenced material. Earlier editions listed in previous editions of this section may be used for components manufactured, designed, or installed in accordance with those earlier editions at the time they were listed. The user must refer to the appropriate previous edition of 49 CFR for a listing of the earlier editions.

(b) All incorporated materials are available for inspection in the Research and Special Programs Administration, 400 Seventh Street, SW., Washington, DC, and at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC. These materials have been approved for incorporation by reference by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. In addition, materials incorporated by reference are available as follows:

(1) American Gas Association (AGA), 1515 Wilson Boulevard, Arlington, VA 22209.

(2) American Petroleum Institute (API), 1220 L Street, NW., Washington, DC 20005.

(3) The American Society of Mechanical Engineers (ASME), United Engineering Center, 345 East 47th Street, New York, NY 10017.

(4) Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. (MSS), 127 Park Street, NE., Vienna, VA 22180.

(5) American National Standards Institute (ANSI), 11 West 42nd Street, New York, NY 10036.

(6) American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428.

(7) National Fire Protection Association (NFPA), 11 Tracy Drive, Avon, MA 02322.

(8) NACE International, 1440 South Creek Drive, Houston, TX 77084.

(c) The full titles of publications incorporated by reference wholly or partially in this part are as follows. Numbers in parentheses indicate applicable editions:

(1) American Gas Association (AGA): AGA Pipeline Research Committee, Project PR-3-805, "A Modified Criterion for Evaluating the Remaining Strength of Corroded Pipe" (December 1989). The RSTRENG program may be used for calculating remaining strength.

(2) American Petroleum Institute (API):

(i) API 510 "Pressure Vessel Inspection Code: Maintenance Inspection, Rating, Repair, and Alteration" (8th edition, June 1997).

(ii) API 1130 "Computational Pipeline Monitoring" (1st Edition, 1995).

(iii) API Publication 2026 "Safe Access/Egress Involving Floating Roofs of Storage Tanks in Petroleum Service" (2nd edition, April 1998).

(iv) API Recommended Practice 651 "Cathodic Protection of Aboveground Petroleum Storage Tanks" (2nd edition, December 1997).

(v) API Recommended Practice 652 "Lining of Aboveground Petroleum Storage Tank Bottoms" (2nd edition, December 1997).

(vi) API Recommended Practice 2003 "Protection Against Ignitions Arising out of Static, Lightning, and Stray Currents" (6th edition, December 1998).

(vii) API Recommended Practice 2350 "Overfill Protection for Storage Tanks In Petroleum Facilities" (2nd edition, January 1996).

(viii) API Specification 5L "Specification for Line Pipe" (41st edition, 1995).

(ix) API Specification 6D "Specification for Pipeline Valves (Gate, Plug, Ball, and Check Valves)" (21st edition, 1994).

(x) API Specification 12F "Specification for Shop Welded Tanks for Storage of Production Liquids" (11th edition, November 1994).

(xi) API Standard 1104 "Welding Pipelines and Related Facilities" (18th edition, 1994).

(xii) API Standard 620 "Design and Construction of Large, Welded, Low-Pressure Storage Tanks" (9th edition, February 1996, Including Addenda 1 and 2).

(xiii) API Standard 650 "Welded Steel Tanks for Oil Storage" (9th edition, July 1993 (Including Addenda 1 through 4).

(xiv) API Standard 653 "Tank Inspection, Repair, Alteration, and Reconstruction" (2nd edition, December 1995, including Addenda 1 & 2).

(xv) API Standard 2000 "Venting Atmospheric and Low-Pressure Storage Tanks" (4th edition, September 1992).

(xvi) API Standard 2510 "Design and Construction of LPG Installations" (7th edition, May 1995).

(3) American Society of Mechanical Engineers (ASME):

(i) ASME/ANSI B16.9 "Factory-Made Wrought Steel Buttwelding Fittings" (1993).

(ii) ASME/ANSI B31.4 "Liquid Transportation Systems for Hydrocarbons, Liquid Petroleum Gas, Anhydrous Ammonia, and Alcohols" (1992 edition with ASME B31.4a-1994 Addenda).

(iii) ASME/ANSI B31.8 "Gas Transmission and Distribution Piping Systems" (1995)

(iv) ASME/ANSI B31G "Manual for Determining the Remaining Strength of Corroded Pipelines" (1991).

(v) ASME Boiler and Pressure Vessel Code, Section VIII "Pressure Vessels," Divisions 1 and 2 (1995 edition with 1995 Addenda).

(vi) ASME Boiler and Pressure Vessel Code, Section IX "Welding and Brazing Qualifications" (1995 edition with 1995 Addenda).

(4) Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. (MSS):

(i) MSS SP-75 "Specification for High Test Wrought Butt Welding Fittings" (1993).

(ii) [Reserved]

(5) American Society for Testing and Materials (ASTM):

(i) ASTM Designation A 53 "Standard specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated Welded and Seamless" (A 53-96).

(ii) ASTM Designation: A 106 "Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service" (A 106-95).

(iii) ASTM Designation: A 333/A 333M "Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service"(A 333/A 333M-94).

(iv) ASTM Designation: A 381 "Standard Specification for Metal-Arc-Welded Steel Pipe for Use With High-Pressure Transmission Systems" (A 381-93).

(v) ASTM Designation: A 671 "Standard Specification for Electric-Fusion- Welded Steel Pipe for Atmospheric and Lower Temperatures" (A 671-94).

(vi) ASTM Designation: A 672 "Standard Specification for Electric-Fusion-Welded Steel Pipe for High-Pressure Service at Moderate Temperatures" (A 672-94).

(vii) ASTM Designation: A 691 "Standard Specification for Carbon and Alloy Steel Pipe Electric-Fusion-Welded for High- Pressure Service at High Temperatures" (A 691-93).

(6) National Fire Protection Association (NFPA):

(i) ANSI/NFPA 30 "Flammable and Combustible Liquids Code," (1996).

(ii) [Reserved]

(7) NACE International (NACE):

(i) NACE Standard RP0169-96, "Control of External Corrosion on Underground or Submerged Metallic Piping Systems' (1996).

(ii) [Reserved]

[Amdt. 195-22, 46 FR 38360, July 27, 1981; 47 FR 32721, July 29, 1982, as amended by Amdt. 195-32, 49 FR 36860, Sept. 20, 1984; 58 FR 14523, Mar. 18, 1993; Amdt. 195-52, 59 FR 33396, June 28, 1994; Amdt. 195-56, 61 FR 26123, May 24, 1996; 61 FR 36826, July 15, 1996; Amdt. 195-61, 63 FR 7723, Feb. 17, 1998; Amdt. 195-62, 63 FR 36376, July 6, 1998; Amdt. 195-66, 64 FR 15934, Apr. 2, 1999; 65 FR 4770, Feb. 1, 2000; Amdt. 195-73, 66 FR 67004, Dec. 27, 2001]